Sunny MCU and Electronics: เมษายน 2014

วันศุกร์ที่ 25 เมษายน พ.ศ. 2557

Thomson TG585 v7

เราเตอร์ตัวนี้เสียแล้วแล้วดังนี้นจะมีแต่ภาพไอซี

รูปตัวเครื่อง

ด้านหน้า

ด้านหลัง

ใต้เครื่อง

สติกเกอร์1

สติกเกอร์2

ภายในเครื่องมีชิ้นส่วนหลักๆ คือ

บอร์ดด้านบน

BROADCOM BCM6338 -> CPU

BROADCOM BCM6338

SPANSION S29GL032A -> Flash 4 MB

SPANSION S29GL032A

BROADCOM BCM5325 -> Ethernet Switch

BROADCOM BCM5325

BROADCOM BCM4318 -> 802.11b/g Transceiver with BroadRange® Technology

SiGe 2528L -> 2.4 GHz Power Amplifier with Power Detector

Wireless & PA

ST 613I -> Regulator

ST 613I

KA7812 -> 3-Terminal 1A Positive Voltage Regulator

KA7812

ใต้บอร์ดมีชิ้นส่วนหลักๆ คือ

ใต้บอร์ด

SAMSUNG K4S281632K -> SDRAM 16 MB

SAMSUNG K4s281632K

SC1202 -> 600mA Low Dropout Positive Voltage Regulator

SC1202

8E764 -> Switching Regulator

8E764

ฺBillion Wireless-N ADSL2+ Firewall Router จาก TRUE

เราเตอร์ตัวนี้เป็นเราเตอร์ได้จาก TRUE ผมได้มาในสภาพเสีย ไอซีระเบิดเปิดไม่ติดแล้วจึงไม่มีส่วนซอฟต์แวร์ให้ดูครับ

ภายนอกเครื่อง

ด้านหน้า

ด้านหลัง

ใต้เครื่อง

สติกเกอร์

แกะออกมาจะเจอบอร์ดด้านล่างก่อนซึ่งไม่มีไอซีใดๆ

ใต้บอร์ด

บอร์ดด้านบนมีชิ้นส่วนหลักๆ คือ

บอร์ดด้านบน

TRENDCHIP TC3162U -> CPU

TRENDCHIP TC3162U

EtronTech EM63A165TS -> SDRAM ขนาด 32 MB

Etrontech EM63A165TS

Winbond 25Q64 -> SPI Flash ขนาด 8 MB

Winbond 25Q64

TrendChip TC2206 -> Ethernet Switch

TrendChip TC2206

Ralink RT3390L -> Wireless

Ralink RT3390L

TrendChip TC3086 -> ADSL ไอซีตัวนี้ระเบิด

TrendChip TC3086

LD1117-1.5 -> LDO Regulator 1.5v

LD1117-1.5

LD1117 -> LDO Regulator

LD1117

LSC LSP5522L -> 2A 18V Synchronous Buck Converter

LSC LSP5522L

ACT4060A -> Wide Input 2A Step Down Converter

ACT4060A

LM317K -> HIGH CURRENT 1.3V TO 37V ADJUSTABLE VOLTAGE REGULATOR

LM317K

วันพฤหัสบดีที่ 24 เมษายน พ.ศ. 2557

Billion BiPAC 5200G R4

อุปกรณ์ตัวนี้คือ 802.11g ADSL2+ Firewall Router มี 1 DSL 4 LAN เสา 1 ต้น

รูปตัวเครื่อง

ด้านหน้า

ด้านหลัง

ใต้เครื่อง

สติเกอร์

ภายในเครื่อง ตัว CPU, Ethernet Switch, และ DSL มี Heatsink แปะอยู่ ชิ้นส่วนสำคัญๆ คือ

บอร์ดด้านบน

Flash -> cFeon EN29LV160 ขนาด 2 MB

RAM -> EtronTech EM638165TS เป็น SDRAM ขนาด 8 MB

CPU & Switch, Flash & RAM & DSL

Wireless -> Ralink RT2561T

Ralink RT2561T

2.4 GHz Transceiver Chip -> Ralink RT2527L

Ralink RT2527L

NEC 2035 -> NEC's BROADBAND GaAs MMIC DPDT SWITCH FOR 2.4 GHz AND 5 GHz WLAN

NEC 2035

SST 12LP14A -> 2.4 GHz Power Amplifier

SST 12LP14A

พอร์ต Serial ความเร็ว 115200

พอร์ต Serial

ใต้บอร์ด มีไอซีหลักๆ คือ

ใต้เครื่อง

ATMEL 93C66A -> Three-wire Serial EEPROM ขนาด 4 kB

ATMEL 93C66A

ภาคจ่ายไฟ ใช้ไอซี 3 ตัวซึ่งเป็นเบอร์เดียวกันคือ

ภาคจ่ายไฟ

AP1509 -> 150KHz, 2A PWM BUCK DC/DC CONVERTER

AP1509

Boot Message รหัสผ่านคือ 3bb

Bootbase Version: VTC1.15 | 2007/11/12 17:18:52

RAM: Size = 8192 Kbytes

DRAM POST: Testing: 8192K

OK

FLASH: AMD 16M *1

RAS Version: 2.11.82.0(RE2.C29)3.11.11.52

System ID: $2.11.82.0(RE2.C29)3.11.11.52 20090627_V004| 2009/06/27

Press any key to enter debug mode within 3 seconds.

............................................................

Copyright (c) 2001 - 2006 ADSL Company

initialize ch = 0, IP175C, ethernet address: 00:04:ed:d2:ef:88

initialize ch = 1, ethernet address: 00:04:ed:d2:ef:88

Wan Channel init ........ done

Initializing ADSL F/W ........ done

==>natTableMemoryInit

<==natTableMemoryInitANNEXAIJLM

old model check flag: on.

new model check flag: on.

product/customer/version number: 3122/2/0

largeD flag=2 (0:maxD=64, 1:maxD=128, 2:maxD=511)

Syncookie switch On!

Press ENTER to continue...

Enter Password : XXXX

Password is not correct

Enter Password : XXX

Password is not correct

Enter Password : XXX

Copyright (c) 2001 - 2006 ADSL Company

router> help

Valid commands are:

sys exit ether wan

ip bridge dot1q pktqos

show set lan

Router Information

router> show all

RAS version: 2.11.82.0(RE2.C29)3.11.11.52

System ID: $2.11.82.0(RE2.C29)3.11.11.52 20090627_V004[Jun 27 2009 16:55:54]

romRasSize: 1280084

system up time: 0:01:48 (2a54 ticks)

bootbase version: VTC1.15 | 2007/11/12

Hostname = router

Message = <empty>

ip route mode = Yes

bridge mode = Yes

DHCP setting:

DHCP Mode = Server

Client IP Pool Starting Address = 192.168.1.2

Size of Client IP Pool = 29

Primary DNS Server = 0.0.0.0

Secondary DNS Server = 0.0.0.0

DHCP server leasetime = 86400

TCP/IP Setup:

IP Address = 192.168.1.1

IP Subnet Mask = 255.255.255.0

Rip Direction = None

Version = Rip-1

Multicast = None

RemoteNode = 0

Rem Node Name = Node1(ISP)

Encapsulation = PPPoE

Multiplexing = LLC-based

Channel active = Yes

VPI/VCI value = 0/33

IP Routing mode= Yes

Bridge mode = No

PPP Username = ye8cz39e8d@3bbnex

PPP password = wfcXYJkq

Service name = A06817750506

Remote IP Addr = 0.0.0.0

Remote IP Subnet Mask = 0.0.0.0

IP address assignment type = Dynamic

SUA = Yes

Multicast = None

Default Route node = Yes

RemoteNode = 1

Rem Node Name = Node2

Encapsulation = RFC 1483

Multiplexing = LLC-based

Channel active = No

VPI/VCI value = 0/34

IP Routing mode= No

Bridge mode = Yes

Remote IP Addr = 0.0.0.0

Remote IP Subnet Mask = 0.0.0.0

IP address assignment type = Dynamic

SUA = Yes

Multicast = None

Default Route node = No

RemoteNode = 2

Rem Node Name = Node3

Encapsulation = RFC 1483

Multiplexing = LLC-based

Channel active = No

VPI/VCI value = 0/35

IP Routing mode= No

Bridge mode = Yes

Remote IP Addr = 0.0.0.0

Remote IP Subnet Mask = 0.0.0.0

IP address assignment type = Dynamic

SUA = No

Multicast = None

Default Route node = No

RemoteNode = 3

Rem Node Name = Node4

Encapsulation = RFC 1483

Multiplexing = LLC-based

Channel active = No

VPI/VCI value = 0/36

IP Routing mode= No

Bridge mode = Yes

Remote IP Addr = 0.0.0.0

Remote IP Subnet Mask = 0.0.0.0

IP address assignment type = Dynamic

SUA = No

Multicast = None

Default Route node = No

RemoteNode = 4

Rem Node Name = Node5

Encapsulation = RFC 1483

Multiplexing = LLC-based

Channel active = No

VPI/VCI value = 0/37

IP Routing mode= No

Bridge mode = Yes

Remote IP Addr = 0.0.0.0

Remote IP Subnet Mask = 0.0.0.0

IP address assignment type = Dynamic

SUA = No

Multicast = None

Default Route node = No

RemoteNode = 5

Rem Node Name = Node6

Encapsulation = RFC 1483

Multiplexing = LLC-based

Channel active = No

VPI/VCI value = 0/38

IP Routing mode= No

Bridge mode = Yes

Remote IP Addr = 0.0.0.0

Remote IP Subnet Mask = 0.0.0.0

IP address assignment type = Dynamic

SUA = No

Multicast = None

Default Route node = No

RemoteNode = 6

Rem Node Name = Node7

Encapsulation = RFC 1483

Multiplexing = LLC-based

Channel active = No

VPI/VCI value = 0/39

IP Routing mode= No

Bridge mode = Yes

Remote IP Addr = 0.0.0.0

Remote IP Subnet Mask = 0.0.0.0

IP address assignment type = Dynamic

SUA = No

Multicast = None

Default Route node = No

RemoteNode = 7

Rem Node Name = Node8

Encapsulation = RFC 1483

Multiplexing = LLC-based

Channel active = No

VPI/VCI value = 0/40

IP Routing mode= No

Bridge mode = Yes

Remote IP Addr = 0.0.0.0

Remote IP Subnet Mask = 0.0.0.0

IP address assignment type = Dynamic

SUA = No

Multicast = None

Default Route node = No

ASUS DSL-N10 A1

อุปกรณ์ตัวนี้คือ All in One Router โดยมี 1 DSL 4 LAN ไวเลสความเร็ว 150 Mbps เสาอากาศถอดได้ 1 เสา
รูปตัวเครื่อง

ด้านหน้า

ด้านหลัง

ใต้เครื่อง

เราเตอร์ตัวนี้มี CPU 2 ชุด คือของ ADSL และของเราเตอร์ มีชิ้นส่วนหลักๆ คือ

บอร์ดด้านบน

Router CPU -> Ralink RT3050F

Ralink RT3050F

Router RAM -> Winbond W9825G6JH-6 เป็น SDRAM ขนาด 32 MB

Winbond W9825G6JH-6

Router Flash -> MXIC 25L3206E ขนาด 4 MB

MXIC 25L3206E

ADSL CPU -> TRENDCHIP TC3162LE

TRENDCHIP TC3162LE

ADSL RAM -> Winbond W9816G6IH-6 เป็น SDRAM ขนาด 2 MB

Winbond W9816G6IH-6

ADSL Flash -> MXIC 25L8006E ขนาด 1 MB

MXIC 25L8006E

ADSL IC -> TRENDCHIP TC3086

TRENDCHIP TC3086

.ภาคจ่ายไฟ 6.85v, 3.18v, และ 1.84v ประกอบด้วยไอซี 2 ชนิด คือ

ภาคจ่ายไฟ

LD1117AL -> LOW DROP FIXED AND ADJUSTABLE POSITIVE VOLTAGE REGULATORS

LD1117AL

BH997 -> Switching Regulator

BH997

Regulator 1.96v -> LD1117

LD1117

พอร์ต Serial ของเราเตอร์ความเร็ว 57600

พอร์ต Serial ของเราเตอร์

พอร์ต Serial ของ ADSL ความเร็ว 115200

พอร์ต Serial ของ ADSL

ใต้บอร์ดไม่มีไอซีใดๆ

ใต้บอร์ด

ฺBoot Message ของ ADSL

Bootbase Version: VTC_SPI_BR1.6 | 2010/7/30 16:28:57

RAM: Size = 2048 Kbytes

DRAM POST: Testing: 2048K

OK

Found SPI Flash 1024KiB MX25L8006E at 0xbfc00000

RAS Version: ASUS_ANNEXAIJLM_20120423

System ID: $3.6.18.0(BE.C3)3.16.18.0| 2011/10/31 20111031_v012 | 2011/10/31

Press any key to enter debug mode within 3 seconds.

............................................................

Copyright (c) 2001 - 2006 TrendChip Technologies Corp.

TC2101MB, initialize ch = 0, ethernet address: 00:aa:bb:01:23:45

Wan Channel init ........ done

Initializing ADSL F/W ........ done

ANNEXAIJLM

US bitswap on,DS bitswap on

OlrON

SRAOFF

Press ENTER to continue...

ANNEXAIJLM

SRAOFF

Testlab 11

lanip=194.255.255.254,lanmask=255.255.255.0Dyingasp OFF!

Valid Loss of power OFF!

largeD flag=2 (0:maxD=64, 1:maxD=128, 2:maxD=511)

disable PM!

set try multimode number to 3 (dropmode try num 3)

Password: XXXXX

Copyright (c) 2001 - 2006 TrendChip Technologies Corp.

tc>

tc>

tc>

tc>

tc>

tc>

tc>

tc>

tc>

tc> sys ver

Bootbase Version: VTC_SPI_BR1.6 | 2010/7/30

RAS F/W Version : ASUS_ANNEXAIJLM_20120423

System F/W ID : $3.6.18.0(BE.C3)3.16.18.0| 2011/10/31 20111031_v012 [Oct 31 2011 12:53:59]

DSL FW Version : FwVer:3.16.18.0_TC3086 HwVer:T14.F7_6.0

Standard : Multi-Mode

Country Code : 255

MAC Address : 00:aa:bb:01:23:45

tc> sys tpget sys show sysinfo

syspwd=admin,mac=00:aa:bb:01:23:45,fwver=ASUS_ANNEXAIJLM_20120423 ,adslver= FwVer:3.16.18.0_TC3086 HwVer:T14.F7_6.0tc> sys tpget sys show lan

lanip=194.255.255.254,lanmask=255.255.255.0tc> sys tpget wan atm pvc disp

index=0,active=0,encap=0,mode=0,vid=4095,vpi=0,vci=0,qostype=0,pcr=0,scr=0,mbs=0index=1,active=0,encap=0,mode=0,vid=4095,vpi=14,vci=0,qostype=0,pcr=0,scr=0,mbs=0index=2,active=0,encap=0,mode=0,vid=4095,vpi=0,vci=0,qostype=0,pcr=0,scr=0,mbs=0index=3,active=0,encap=0,mode=0,vid=4095,vpi=8,vci=0,qostype=0,pcr=0,scr=0,mbs=0index=4,active=0,encap=0,mode=0,vid=4095,vpi=0,vci=0,qostype=0,pcr=0,scr=0,mbs=0index=5,active=0,encap=0,mode=0,vid=4095,vpi=0,vci=0,qostype=0,pcr=0,scr=0,mbs=0index=6,active=0,encap=0,mode=0,vid=4095,vpi=0,vci=0,qostype=0,pcr=0,scr=0,mbs=0index=7,active=0,encap=0,mode=0,vid=4095,vpi=0,vci=0,qostype=0,pcr=0,scr=0,mbs=0COMPLETEtc> sys tpget sys show adsl

adslmode=5,adsltype=4,bitswap=0tc> sys tp..

writeRomBlock(): Erase OK!

..se....t wan adsl type 4

OK

tc> sys tpget sys show adsl

adslmode=5,adsltype=4,bitswap=0tc> sys tpget sys show adsl

adslmode=5,adsltype=4,bitswap=0tc> w dmt2 set olr 3

SRAON

tc> sys tpget wan adsl status

current modem status: down

tc> sys tpget wan adsl status

current modem status: down

tc> sys tpget wan adsl status

current modem status: down

tc> sys tpget wan adsl status

current modem status: down

tc> sys tpget wan adsl status

current modem status: down

tc> sys tpget wan adsl status

current modem status: down

tc>

Boot Message ของเราเตอร์

U-Boot 1.1.3 (Sep 26 2011 - 19:25:07)

Board: Ralink APSoC DRAM: 32 MB

relocate_code Pointer at: 81a40000

spi_wait_nsec: 3e

spi deice id: c2 20 16 c2 20 (2016c220)

find flash: mx25l3205d

Using default environment

============================================

Ralink UBoot Version: 3.5 (09/26/2011)

--------------------------------------------

ASIC 3050F (DSL-N10) (Port5<->None)

DRAM component: 256 Mbits SDR

DRAM bus: 16 bit

Total memory: 32 MBytes

Flash component: SPI Flash

Date:Sep 26 2011 Time:19:25:07

============================================

icache: sets:256, ways:4, linesz:32 ,total:32768

dcache: sets:128, ways:4, linesz:32 ,total:16384

##### The CPU freq = 320 MHZ ####

SDRAM bus set to 16 bit

SDRAM size =32 Mbytes

Please choose the operation:

1: Load system code to SDRAM via TFTP.

2: Load system code then write to Flash via TFTP.

3: Boot system code via Flash (default).

4: Entr boot command line interface.

6: Factory block init. Require factory tool to program again.

9: Load Boot Loader code then write to Flash via TFTP. 0

3: System Boot system code via Flash.

Do bootm

## Booting image at bf050000 ...

raspi_read: from:50000 len:40

Image Name:

Created: 2013-08-22 3:09:06 UTC

Image Type: MIPS Linux Kernel Image (lzma compressed)

Data Size: 3600181 Bytes = 3.4 MB

Load Address: 80000000

Entry Point: 80324000

raspi_read: from:50040 len:36ef35

Verifying Checksum ... OK

Uncompressing Kernel Image ... OK

No initrd

## Transferring control to Linux (at address 80324000) ...

## Giving linux memsize in MB, 32

Starting kernel ...

LINUX started...

THIS IS ASIC

Linux version 2.6.21 (asus@localhost) (gcc version 3.4.2) #1915 Thu Aug 22 11:09:00 CST 2013

The CPU feqenuce set to 320 MHz

CPU revision is: 0001964c

Determined physical RAM map:

memory: 02000000 @ 00000000 (usable)

Initrd not found or empty - disabling initrd

Built 1 zonelists. Total pages: 8128

Kernel command line: console=ttyS1,57600n8 root=/dev/ram0

Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.

Primary data cache 16kB, 4-way, linesize 32 bytes.

Synthesized TLB refill handler (20 instructions).

Synthesized TLB load handler fastpath (32 instructions).

Synthesized TLB store handler fastpath (32 instructions).

Synthesized TLB modify handler fastpath (31 instructions).

Cache parity protection disabled

cause = 1080000c, status = 1100ff00

PID hash table entries: 128 (order: 7, 512 bytes)

calculating r4koff... 00138800(1280000)

CPU frequency 320.00 MHz

Using 160.000 MHz high precision timer.

Console: colour dummy device 80x25

Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)

Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)

Memory: 26476k/32768k available (2712k kernel code, 6292k reserved, 499k data, 2564k init, 0k highmem)

Mount-cache hash table entries: 512

NET: Registered protocol family 16

SCSI subsystem initialized

Time: MIPS clocksource has been installed.

NET: Registered protocol family 2

IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

TCP established hash table entries: 1024 (order: 1, 8192 bytes)

TCP bind hash table entries: 1024 (order: 0, 4096 bytes)

TCP: Hash tables configured (established 1024 bind 1024)

TCP reno registered

detected lzma initramfs

detected lzma initramfs

initramfs: LZMA lc=3,lp=0,pb=2,dictSize=1048576,origSize=9634304

LZMA initramfs by Ming-Ching Tiew <mctiew@yahoo.com>....................................................................................................................................................<6>squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher

squashfs: LZMA suppport for slax.org by jro

fuse init (API version 7.8)

io scheduler noop registered (default)

Ralink gpio driver initialized

spidrv_major = 217

HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096

N_HDLC line discipline registered.

Serial: 8250/16550 driver $Revision: 1.3 $ 2 ports, IRQ sharing disabled

serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A

serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A

RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize

loop: loaded (max 8 devices)

PPP generic driver version 2.4.2

PPP Deflate Compression module registered

PPP BSD Compression module registered

PPP MPPE Compression module registered

NET: Registered protocol family 24

PPPoL2TP kernel driver, V0.18.3

PPTP driver version 0.8.5

block2mtd: version $Revision: 1.1.1.1 $

spi_wait_nsec: 72

deice id : c2 20 16 c2 20 (2016c220)

mx25l3205d(c2 20160000) (4096 Kbytes)

mtd .name = raspi, .size = 0x00400000 (4M) .erasesize = 0x00010000 (64K) .numeraseregions = 0

Creating 5 MTD partitions on "raspi":

0x00000000-0x00400000 : "ALL"

0x00000000-0x00030000 : "Bootloader"

0x00030000-0x00040000 : "Config"

0x00040000-0x00050000 : "Factory"

0x00050000-0x00400000 : "Kernel"

nf_conntrack version 0.5.0 (16384 buckets, 8192 max)

ipt_time loading

ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone

arp_tables: (C) 2002 David S. Miller

TCP cubic registered

NET: Registered protocol family 1

NET: Registered protocol family 10

NET: Registered protocol family 17

802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>

All bugs added by David S. Miller <davem@redhat.com>

GDMA1_MAC_ADRH -- : 0x00000000

GDMA1_MAC_ADRL -- : 0x00000000

Ralink APSoC Ethernet Driver Initilization. v2.00 64 rx/tx descriptors allocated, mtu = 1500!

NAPI enable, weight = 0, Tx Ring = 64, Rx Ring = 64

GDMA1_MAC_ADRH -- : 0x0000000c

GDMA1_MAC_ADRL -- : 0x43305077

PROC INIT OK!

Freeing unused kernel memory: 2564k freed

devpts: called with bogus options

mount: mounting none on /proc/bus/usb failed: No such file or diAlgorithmics/MIPS FPU Emulator v1.5

rectory

nvram_linux: no version for "struct_module" found: kernel tainted.

spi deice id: c2 20 16 c2 20 (2016c220)

find flash: mx25l3205d

Loader version is 1

Checking RST BTN..

[ra setdir]: 880

RST BTN check done..

dump trx header..

1+0 records in

1+0 records out

rt2860v2_ap: module license 'unspecified' taints kernel.

insmod: dwc_otg.ko: module not found

*** value_str

[rc Chk sw_mode/ex] [1][]

*** value_str

--- AP mode ---

rmmod: nf_nat_rtsp: No such file or directory

waitpid: No child processes

rmmod: nf_conntrack_rtsp: No such file or directory

waitpid: No child processes

BSSID number: 1

--- init_switch_mode ---

Open pseudo device failed

Open pseudo device failed

[ra setdir]: 880

sw_mode= 1

gen ralink config

[rc] main_loop: state= 2

chk ver:0710

[rc] START

vconfig...

GDMA1_MAC_ADRH -- : 0x0000c860

GDMA1_MAC_ADRL -- : 0x005bd180

waitpid: No child processes

waitpid

phy_tx_ring = 0x01192000, tx_ring = 0xa1192000

phy_rx_ring = 0x00000000, rx_ring = 0x00000000

: No child proceRT305x_ESW: Link Status Changed

sses

CDMA_CSG_CFG = 81000007

GDMA1_FWD_CFG = 710000

[K] rtmp nv init: read from:40000

[RtmpFlashRead] from:(40000)

[RtmpFlashRead] b:(200)

[RtmpFlashRead] p:(c0268034)

[ra flash conf 3]

RT305x_ESW: Link Status Changed

0x1300 = 00064380

eth2.2: Setting MAC address to c8 60 00 5b d1 80.

VLAN (eth2.2): Underlying device (eth2) has same MAC, not checking promiscious mode.

waitpid: No child processes

dsl_config_num=0

wanport=0, stbport=0

waitpid: No child processes

waitpid: No child processes

waitpid: No child processes

eth2.1: dev_set_promiscuity(master, 1)

device eth2 entered promiscuous mode

device eth2.1 entered promiscuous mode

waitpid: No child processes

device ra0 entered promiscuous mode

[rc] not repeater mode [192.168.1.1][]

## [rc] set lan_if as 19br0: port 2(ra0) entering listening state

2.168.1.1/255.25br0: port 1(eth2.1) entering listening state

5.255.0

tp_init uses obsolete (PF_INET,SOCK_PACKET)

set default filter settings

waitpid: No child processes

start services...

[rc] start services

br0: port 2(ra0) entering learning state

br0: port 1(eth2.1) entering learning state

starting...

info, udhcp server (v0.9.8-asus) started

***** g_wl_interface = ra0 ******

--- START: Wait to start wanduck ---

Delay rubr0: topology change detected, propagating

n wanduck 3 secobr0: port 2(ra0) entering forwarding state

nds

br0: topology change detected, propagating

br0: port 1(eth2.1) entering forwarding state

RT305x_ESW: Link Status Changed

resume stp forwarding delay and hello time

waitpid: No child processes

start_wan

Set: phy[0].reg[0] = 3100

Set: phy[1].reg[0] = 3100

Set: phy[2].reg[0] = 3100

Set: phy[3].reg[0] = 3100

internet_led exit

failover_monitor exit

sh: failover_3g: not found

killall: telnetd: no process killed

Open pseudo device failed

Open pseudo device failed

[ra setdir]: 880

upnp will be delayed 10 secs

Password for 'admin' changed

pool.ntp.org: Unknown host

start wsc

WPS: PIN

waitpid: No child processes

BusyBox v1.12.1 (2013-08-22 03:05:02 GMT) built-in shell (ash)

Enter 'help' for a list of built-in commands.

# libupnp: using UDP SSDP_PORT = 1900

## wsc upnp dev start ##

## USE XML TEMPLATE ##

## create device desc xml:/etc_ro/xml//WFADeviceDesc.xml ##

dump all description files:

# Enable direct rule

[wd] chk usb plugin

[rc] main_loop: [k] track_flag=0, clean_flag=0, mm_flag=0, ipaddr=0

state= 6

## rc recv HOTPLUG:none

track set 501

track ok:0

SIGTTIN: do nothing

[rc] main_loop: state= 4

SG,Detect_list.txt

Auto_detect init...

msgget ok

MSQ_to_daemon : 0

MSQ_from_daemon : 32769

msgsnd ok (IPC_CLIENT_MSG_Q_ID)

#

cpuinfo

# cat /proc/cpuinfo

system type : Ralink SoC

processor : 0

cpu model : MIPS 24K V4.12

BogoMIPS : 212.99

wait instruction : yes

microsecond timers : yes

tlb_entries : 32

extra interrupt vector : yes

hardware watchpoint : yes

ASEs implemented : mips16 dsp

VCED exceptions : not available

VCEI exceptions : not available

mtd

# cat /proc/mtd

dev: size erasesize name

mtd0: 00400000 00010000 "ALL"

mtd1: 00030000 00010000 "Bootloader"

mtd2: 00010000 00010000 "Config"

mtd3: 00010000 00010000 "Factory"

mtd4: 003b0000 00010000 "Kernel"

ไฟล์ mtd